#Jt65 mkii ic 7800 how to#
#Jt65 mkii ic 7800 install#
#Jt65 mkii ic 7800 drivers#
#Jt65 mkii ic 7800 driver#
#Jt65 mkii ic 7800 manual#

Suffice to say it is quite straightforward if you accept most of the default options and along the way you will be faced with some setup screens which I will try to cover off below. It is well documented on the WSJT-X website and the user guide is available for download.ДЄlso, software tends to change over time and so me describing the installation process one day could be completely out of date on the next version. There is little point in my describing the installation process. Section 5 - Download and Installation of the WSJT-X Software Make a note of which one you have as you will need to know the name when you are configuring the audio section of your Digimode software. I have both versions of the sound chip installed on my PC shown and highlighted below just for demonstration purposes. ' C-Media USB Headphone Set' or 'USB PnP Sound Device'

The C-Media chip can present itself as one of two names under Windows.

#Jt65 mkii ic 7800 driver#

Most operating systems have an in-box driver for the C-Media chip.ДЄgain using Device Manger, you can check to see what name the interface has been allocated. If you have purchased a USB-Digimode-3В interface from us, this uses the C-Media CM108 chipset. You will see it vanish and reappear in the list. If you are unsure which comm port it is, unplug it and plug it back in. In the example below, the USB interface has been allocated COM62.

#Jt65 mkii ic 7800 drivers#

Once you have the drivers installed, you can make a note of the comm port the interface has inherited using Windows device manager under the Ports (COM & LPT) section. For Windows, I find the best option is to use the 'setup executable ' link that you can see in the comments section at the end of the Windows row.

#Jt65 mkii ic 7800 install#

They are available from the the FTDI website here:Дownload and install the appropriate driver for your operating system. If you have a USB-Digimode-1,В USB-Digimode-2 or one of our USB CAT Interfaces, you may need to install the FTDI Drivers USB comm port drivers. On the digimode interface solutions, the CAT plug will either be coded YellowВ or the outgoing cable will be labelled on the lid of the interface box.

This may be labelled CAT, CI-V or COMM depending on your radio type. On the Digimode-1 and CAT interface cables, plug the CAT plug into the CAT port of the radio.

#Jt65 mkii ic 7800 manual#

Check your transceiver manual to confirm which port is used for a data/packet modem connection. Plug the data Din or Mini Din plug into the Data/Accessory/Packet port of your radio.

Plug in the Tx/Rx audio and PTT data PlugsДЇor the Digimode-1, Digimode-2, Digimode-3 and audio cable solutions, the data plug will be a Din or Mini Din plug and labelled on the lid of the box (if it needs to be identified).

You can check the installation following section 5. The USB-Digimode-3 Sound Card interface has in-box drivers in most operating systems and so is 'driver free'. More on loading the drivers in Section 4. This may cause your operating system to pop up a message if the drivers are not loaded. On the Digimode-1, Digimode-2, Digimode-3 and USB CAT Interfaces, insert the USB A Type plug into a free USB port on your PC. Just pop TRRS splitter in the search box and you will find plenty of sellers. These are available from sites like eBay for a few $. If you have a modern laptop with a 4 pole Headset jack, you will need a splitter. Insert the Blue coded jack into the Microphone input of your PCs sound card. InsertВ the Green coded jack into the Line/Headphone output of your PCs sound card.Дў. These instructions were written around installing on Windows 10 but you will get the idea for other operating systems.ДЇirst step is to plug the Digimode interface or CAT cables into the USB Ports on your PC and into the CAT and Data ports on your transceiver.ДЇor allВ our interfaces and cables with the separate Green and Blue coded 3.5mm audio jacks.ДЎ. This guide aims to get you set up and running using WSJT-X and using the modes that it makes available to you.Д«eing a manufacturer of both CAT and Digital Mode interfaces, excuse us for biasing the set-up instructions towards our products but hopefully, this guide will apply to many products. WSJT-X implements communication protocols or 'modes' called FT4, FT8, JT4, JT9, JT65, QRA64, ISCAT, MSK144, and WSPR

#Jt65 mkii ic 7800 how to#

How to set up WSJT-X for using FT8 and other modes.

Jt65 mkii ic-7800